Published By
Created On
15 Nov 2020 06:11:19 UTC
Transaction ID
Cost
Safe for Work
Free
Yes
Aussie50 - 20130112 - Tubed 13 inch Tire Pop with Water Pressure - 9MCORuhvLOM
Very old dry rotted trailer tire took a lot more pressure than I expected to fail!
rotted to the point where bits were falling off it, but the static pressure test shows how strong the casing plies and radial belts are
Next one, 235/70/16 OEM Mazda Tribute tire and wheel!
rotted to the point where bits were falling off it, but the static pressure test shows how strong the casing plies and radial belts are
Next one, 235/70/16 OEM Mazda Tribute tire and wheel!
Author
Content Type
Unspecified
video/mp4
Language
Unspecified
More from the publisher
Controlling
VIDEO
AUSSI
Aussie50-20140119-Hisense-42-Inch-LED-LCD-TV-Teardown-DLlyIlzqycsmp4
Tearing into a junk LCD that was found on the roadside - very simple compared to older sets of the same size.
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
Controlling
VIDEO
AUSSI
Aussie50-20110430-Machining-304-Stainless-Shaft-for-DC-Motor-GmhEHtKlQdgmp4
lbry://@Aussie50-archive/Aussie50-20110430-Machining-304-Stainless-Shaft-for-DC-Motor-GmhEHtKlQdgmp4
Motor unit is for spinning the Westinghouse armature and polishing the commutator bars.
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
Controlling
VIDEO
AUSSI
Aussie50-20111006-Scrap-Find-Sony-TFT-LCD-Monitor-Test-iPcyc9DZQ9cmp4
I was expecting this to be a repair video, but apparently no repair is needed :p
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
Controlling
VIDEO
AUSSI
Aussie50-20110617-Projects-Update-and-new-Game-Rants-xXI8lTmZpfwmp4
most new games suck ass because of 'COD' Syndrome :(. long live the real shooters like DN3d, Quake 2, half-Life and Doom
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
Controlling
VIDEO
AUSSI
Aussie50-20151006-Ramblotron-entry-October-5-2015-uYrwWYbapicmp4
Back from holiday, and a new car comes to stay!
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
Controlling
VIDEO
AUSSI
Aussie50-20130718-Battenfeld-Plus-350V-Autopsy-Pt1-Up-to-your-armpits-in-oil-ngntUHeiwUcmp4
Time to turn it into a massive pile of hobby spares!, the 1" thick steel plates in it will be infinitely useful in a upcoming shredder project :D
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
Controlling
VIDEO
AUSSI
Aussie50-20190405-Ripping-down-304-stainless-manual-lathe-B0asSNXQm0Ymp4
Just a short cellphone video, I make dozens of these each year, not going to share mission-critical data but just facing to length then turning a spigot on some 76mm (3") 304 stainless steel bar. actual dimensions were 24mm OAL, spigot was 64mm X 10mm.
Following processes see it drilled 30mm, bored to 34mm and counter-bored to 48mm prior to die-sink EDM work.
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
Controlling
VIDEO
AUSSI
Aussie50-20101103-Nissan-Datsun-L18-4Cyl-High-Quality-Run-dTSnxH2jrwUmp4
Ignition still mis fires but I will work that out soon.
apart from that this engine is good to go!.
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4
Controlling
VIDEO
AUSSI
Aussie50-20090708-July9-2009-Scrap-Run-wkXPf6u2EhMmp4
One of my Fortnightly scrap collections
I always try and reuse parts of old machines before deciding to scrap them.
The coil end plates were given to me by a good friend who is in the scrap bis, but cannot justify paying sombody $20 an hr to clean them for a small amount of copper (compared with the hourly wage)
Transaction
Created
3 weeks ago
Content Type
Language
video/mp4