I wanted to make a box to hold my comic books collection and I needed a reason to try out my Incra box joint jig. Subscribe to my channel: http://bit.ly/1k8msFr What you'll need: http://amzn.to/1IZxDbg - Wood glue http://amzn.to/1JeObO3 - Table Saw http://amzn.to/1SVz1Ub - Formby's Tung Oil Finish http://amzn.to/1fqtm69 - Corner clamps http://amzn.to/1fqt9Qf - Incra Box joint jig http://amzn.to/1WFP9Zo - 8" dado stack http://amzn.to/1hNmjpS - Trim router MORE PROJECTS, POSTS AND EVENTS http://www.iliketomakestuff.com Want to support ILTMS? There are lots of ways .. find out more at http://www.iliketomakestuff.com/support BUY A SHIRT, STICKER OR A HANDMADE ITEM!! http://www.iliketomakestuff.com/store FOLLOW: http://facebook.com/iltms http://twitter.com/iliketomakestuf http://instagram.com/iliketomakestuff I cut one piece of 1/2" plywood down to 24"x24". This will become the side panels. I ripped another piece to 8 1/2" wide to use as the ends. I switched out the blade for a dado set, so I could cut 1/4" dados. I set the saw to only cut 1/4" deep. I cut a dado every inch across the whole board. I left 1 1/2" on each end. This piece was cut in half, perpendicular to the dados. I trimmed the end pieces to the same height as the side panels. This is my first time using this Incra box joint jig. It takes a little bit to setup, but then it's very easy to use. I clamped together the end pieces and cut finger joints on one side. Keeping them lined up, I moved the clamps to the other side. Then I cut matching fingers on the other edge. I clamped together the side panels. Then I cut fingers on both ends of the panels. The cut outs were cleaned up with a rolled up piece of sandpaper. On each piece, I clamped down a straight edge about 3" up. I used this as a guide to cut a rabbet along the bottom edge of all four pieces. I added glue to all of the cut outs, then assembled the finger joints. The joints were tight enough to have to be forced together (that's good). I used some clamping pressure to pull them all of the way together. For glue drying, I added corner clamps to keep the corners square. After it dried, I added glue to the rabbet. I cut a piece of 1/4" mdf to fit and dropped it in place. I added some weight to make good surface contact while the glue dried. I set a stop block on my sled and cut several pieces of MDF to act as dividers. 1/4" was what I had on hand, but 1/8 would be a better choice. I clamped the dividers and rounded the bottom corners, so they would slide into the dados easily. Then I test fitted the dividers and sanded as needed. With an orbital sander, I sanded all of the finger "tips" flush, being sure not to sand away the top layer of veneer. The whole box got a couple of coats of varnish. Then I just had to move over all of my comics! Second channel: bit.ly/iltms-2

I made a guitar from a shovel for Rob Scallon to play! Check out his video https://youtu.be/IyQOw-_H4yE Subscribe to my channel: http://bit.ly/1k8msFr MORE PROJECTS, POSTS AND EVENTS http://www.iliketomakestuff.com HERE'S WHAT I USED: A Shovel http://amzn.to/1SVIBG6 - Bandsaw http://amzn.to/1GMrfGL - Dewalt 20v drill driver combo http://amzn.to/1Svkg9N - Files http://amzn.to/1gjdrqU - Angle grinder http://amzn.to/1T0GBNj - Cut off wheels http://amzn.to/1U5NH1C - EMG Pickup http://amzn.to/247L18e - Fender locking tuner http://amzn.to/1DxuSyA - Tekton Precision Screw driver kit Want to support ILTMS? Get early viewing, exclusive content and more... http://www.iliketomakestuff.com/patreon BUY A SHIRT, STICKER, PENCILS and MORE!! http://www.iliketomakestuff.com/store FOLLOW: http://twitter.com/iliketomakestuf http://instagram.com/iliketomakestuff http://facebook.com/iltms Second channel: bit.ly/iltms-2

Learn how to make the tabletop game Othello (or Reversi) Subscribe to my channel: http://bit.ly/1k8msFr Sponsored by : QALO http://qalo.com Second Channel: http://bit.ly/iltms-2 MORE PROJECTS, POSTS AND EVENTS http://www.iliketomakestuff.com Rules for Reversi: https://en.wikipedia.org/wiki/Reversi TOOLS LIST: (some are better than the versions I own) http://amzn.to/2aCJYGu - SawStop cabinet saw http://amzn.to/2aofRls - 8" Dado stack http://amzn.to/2axFfv4 - Dewalt compound miter saw http://amzn.to/2akFubx - Orbital Sander http://amzn.to/2axFiqN - Incra box joint jig http://amzn.to/2aAwoWZ - Push Blocks http://amzn.to/2axPah6 - Grizzly 14" Bandsaw http://amzn.to/2awLSaO - Shop Fox Hanging Air Filter http://amzn.to/2akFN6c - 2HP Dust Collector http://amzn.to/2axPmNA - 1 Micron bag http://amzn.to/2aXHswm - Spray lacquer http://amzn.to/2aAxAtv - Formby's tung oil finished (tung oil/varnish) http://www.inventables.com?ref=iltms - X-Carve (CNC) http://amzn.to/2al6w2q - Heat Gun Want to support ILTMS? Get early viewing, exclusive content and more... http://www.iliketomakestuff.com/patreon BUY A SHIRT, STICKER, PENCILS and MORE!! http://www.iliketomakestuff.com/store FOLLOW: http://twitter.com/iliketomakestuf http://www.twitch.tv/iliketomakestuff http://instagram.com/iliketomakestuff http://facebook.com/iltms https://snapchat.com/add/iliketomakestuf

Check out how I made this fully custom arcade cabinet, powered by a Raspberry Pi, to play retro games! Subscribe to my channel: http://bit.ly/1k8msFr Get digital plans for this cabinet to build your own! http://www.iliketomakestuff.com/product/arcade-cabinet-digital-plan/ Be sure to watch the previous videos in this series: https://www.youtube.com/watch?v=RcsKNryPAzw https://www.youtube.com/watch?v=K3QXLQ1UXqs https://www.youtube.com/watch?v=t4OjP_5HEzs MORE PROJECTS, POSTS AND EVENTS http://www.iliketomakestuff.com HERE'S WHAT I USED: http://amzn.to/1NCVmAb - SawStop cabinet saw http://amzn.to/1GMrfGL - Dewalt 20v drill driver combo http://amzn.to/1Rq3fwG - Arduino Uno http://amzn.to/1T7Gvl0 - LED Strips (2) http://amzn.to/1Rq43kZ - Relay Shield / http://amzn.to/1T7G4XH - Single Relay http://amzn.to/1T7Geyk - Three conductor wire http://amzn.to/1Rq3sQq - PIR Sensor http://amzn.to/1Rq4Lic - Switch http://amzn.to/1Rq4Vq1 - Soldering Iron http://amzn.to/1T7HtO7 - Magnetic catch http://amzn.to/1T7HMZ8 - Receptacle http://amzn.to/1Q9516i - Black wall plate http://amzn.to/1T7IaXH - Wall switch http://ergokiwi.com/#product-offering - Ergo Kiwi knife http://www.ebay.com/itm/NEW-LED-lit-Arcade-Push-Button-Mame-Multicade-Choice-of-5-Colors-/221064005914?roken=cUgayN&soutkn=oUoob4 - LED Arcade buttons http://www.ebay.com/itm/Classic-4-8-way-Arcade-Game-Joystick-Ball-PacMan-Pick-A-Color-Zippy-Joy-Stick-/110934985094?hash=item19d43d8986:m:mJZ20kSdD5JJq2F1Rzc0S9Q - Arcade joystick (Jamma style) http://amzn.to/1nzWRXs - 1/2" Overlay Face Frame concealed hinges http://amzn.to/1nzX3Gb - 48" Piano Hinge http://amzn.to/1WXN368 - 3" Speaker grilles http://amzn.to/1WXN89P - Logitech computer speakers Want to support ILTMS? Get early viewing, exclusive content and more... http://www.iliketomakestuff.com/patreon BUY A SHIRT, STICKER, PENCILS and MORE!! http://www.iliketomakestuff.com/store FOLLOW: http://twitter.com/iliketomakestuf http://instagram.com/iliketomakestuff http://facebook.com/iltms Second channel: bit.ly/iltms-2