Finally got to fly while it's snowing actually FPV-visible giant fluffy flakes! The LED light posts in the lot aren't putting out much IR, so the colors look more normal unless you see an incandescent somewhere, like inside the car. Towards the end, I did some quick flights later that night around the hood to show how much fell. Also still needed to kill 6 packs cause of the wet-out that cut my morning lot session short. Then I had another wet-out when I clipped the pine tree and landed upside down, packing snow into the "Tinyhawk S". Fun times... it just won't die! 12 hours later now, there is double what you see in this video on the ground. If I crashed right now, I'd never find it... so we'll give it another go next snow in a plowed area. FRA: Emax Tinyhawk S Indoor FPV Racing Drone Spare Part 75mm Polypropylene Frame Kit 1-2S AIO: EMAX Tinyhawk S Indoor Drone Part - AIO Flight Controller/VTX/Receiver (VTX Removed) MOT: EMAX 08025 15000KV (from the original stock 1S Tinyhawk) PRO: EMAX Tinyhawk 4 Blade Turtle Mode Avan Propeller CAM: Caddx Beetle CMOS 800TVL FOV 170 4:3 NTSC (Camera Only!, IR filter was also removed) VTX: Caddx FireFly (VTX Only!) 5.8GHz 25mw ANT: URUAV Micro UXII Stubby RHCP Mini FPV Antenna 1.6dBi 5.8GHz BAT: Turnigy Nano-tech 300mah 2S 45~90C Lipo Pack Added JST, 5V Beeper, Silicone Conformal Coating and black glint tape (hopefully I won't lose it with all these mods). I modded the Beetle lens for IR / night vision after removing it from the VTX. I used a VTX from a FireFly, cause it supports SmartAudio. I direct-soldered the "URUAV Micro UXII Stubby RHCP" to the FireFly VTX and secured it between the rear props on the bottom. +0.3g (and growing) of 3M Blenderm tape, Gaffer tape, superglue, welder glue, and hot glue. 33.85g Modded Weight (dry) [+5.5g] 28.35g Stock Tinyhawk S (dry). +1.41g Taller 15000KV Motors +3.00g Turnigy NanoTech 45~90C Batteries (18g each) 2S AUW is 52 grams. Flight duration is 2-3 minutes on the Nano-techs. 8.68g 4x 0802 15500KV (stock 2S) 10.09g 4x 08025 15000KV (stock 1S) Recorded via ground-based DVR; https://www.immersionrc.com/fpv-produ... https://www.immersionrc.com/fpv-produ... https://www.fatshark.com/product/hdo-... https://caddxfpv.com/products/beetle-v1 Edited with DaVinci Resolve 16.1.1's mad trickery Music: Galaxy - The Island Excerpt from "Terry Mullen, Live @ TIGHT" mix ... https://www.youtube.com/watch?v=EXU7_vA4dec

More Phantom 4 abuse... I tried to hover a few feet higher than the actual shells were exploding, since the prop wash probably wouldn't shield me from a direct hit as it exploded. It definitely kept all the flying sparks from touching the quad's shell or camera though. Surprising that the proximity to the explosions didn't effect the sensors at all... zero damage to Baro either. No audio... play your own garbage, or do this one in another tab; https://youtu.be/ZrsYD46W1U0?t=14m55s ... https://www.youtube.com/watch?v=pvyOgurA8hs